360-systems Image Server 2000 Bedienungsanleitung Seite 112
- Seite / 135
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Page 112 Image Server 2000 Owner’s Manual
BNC Connectors
The following note applies to all video, LTC, and Genlock connectors:
• A BNC connector used as an output will have 75-ohm source impedance.
• A BNC connector used as an input will have a fixed 75-ohm termination.
GPI Connector
General purpose control inputs (GPI) may be applied to the GPI port, which is a DB-25-F
connector. These inputs are optically isolated from the Image Server circuitry; individual
floating returns are provided. +5 volts may be sourced from pins 21 or 22, or provided from
an external source. Current limiting devices are provided within the Image Server.
General purpose status outputs also appear on the GPI connector. Open-collector outputs are
provided as status outputs, and may be used to drive an external LED or control input.
Refer to the connector pin-out table and partial schematic, following.
GPI Connector Pinout
Pin Signal Pin Signal
1 GPI 1 14 GPI 1 RTN
2 GPI
2 15 GPI
2
RTN
3 GPI
3 16 GPI
3
RTN
4 GPI
4 17 GPI
4
RTN
5 GPI
5 18 GPI
5
RTN
6 GPI
6 19 GPI
6
RTN
7 N/C 20 N/C
8,
9,
10 GND 21,
22 +5V
S
OURCE
(200
M
A
MAX
)
11 GPO
2 23 GPO
1
12 GPO
4 24 GPO
3
13 GPO
6 25 GPO
5
- Contents 3
- Preface 8
- Safety Notices 9
- Introduction 11
- Remote Controls 12
- Extended Feature Set 12
- Audio Features 12
- Reliability Counts 13
- Key Features and Benefits 14
- Available Models 16
- Installation 17
- Rack Mounting 18
- Important Installation Notes 18
- About Image Server Software 20
- Front Panel Features 21
- Rear Panel Drawing 22
- Rear Panel Features 23
- Serial Control Ports 24
- Gigabit Ethernet Port 25
- GPI Control 25
- Genlock Sync Reference 25
- LTC Time Code Input 25
- Basic Operations 27
- On-Screen Main Menu Bar 28
- System Menu Bar 29
- Show Menu 29
- Edit Menu 29
- Windows Menu 30
- Help Menu 30
- The Status Bar 30
- The Transport Channel View 31
- Transport Menu Bar 31
- File Menu 31
- Options Menu 32
- Playlist Menu Bar 33
- Record Configuration Options 35
- Setting the Sync Source 35
- Arming the Audio tracks 37
- Setting the Recording Format 37
- Setting the Time Code Source 38
- Beginning Recording 38
- PLAYING A CLIP FROM THE GUI 41
- Ejecting a Clip 42
- Using Jog 42
- Using GO-TO 42
- Using Fast Forward / Rewind 42
- EDITING A CLIP 43
- SYSTEM CONFIGURATION 45
- Programming GPIO Outputs 46
- Programming GPIO Inputs 47
- Configuring the Network 48
- Setting the Date and Time 50
- Calibrating Channels 51
- CLIP NAVIGATOR 52
- Finding Clips 53
- USING PLAYLISTS 55
- The Playlist view 56
- Stopping a Playlist (STOP) 58
- APPENDIX D – PLAYLIST 60
- MANAGEMENT DETAIL 60
- EDITING PLAYLISTS 61
- Figure 23 - GPO Editor 64
- Advanced Topics 65
- Using Embedded Audio 66
- Using Channel Ganging 68
- Animation Import 70
- Still Frames 70
- FTP File Transfers 71
- Figure 26 73
- Network Time Protocol 75
- Configuring NTP 76
- Selecting the Time Zone 76
- Entering Network Parameters 77
- Automation Control 79
- Other Automation Options 81
- Remote Workstation Interface 84
- System Requirements 85
- Operations 85
- After Installation 86
- Hard Disk Management 88
- Managing Disk Arrays 89
- Rebuilding the RAID Array 96
- Replacing Hard Drives 96
- Maintenance 97
- Access to Components 98
- General Handling Precautions 99
- Accessing the Motherboard 100
- JUMPER BLOCK PAIR SHOWN 101
- IN ANALOG POSITION 101
- IN DIGITAL POSITION 101
- GAIN ADJUST 101
- Audio Level Calibration 102
- Program Updates via CD-ROM 104
- Replacing a Hard Drive 105
- Factory Repair Policy 105
- Regulatory Certifications 106
- Product Warranty 108
- End User License Agreement 109
- Appendix A 111
- Connector Specifications 111
- BNC Connectors 112
- GPI Connector 112
- GPI Connector Pinout 112
- System Board Ports 114
- Appendix B 115
- Serial Command Protocols 115
- BVW Serial Command Table 117
- Odetics® Protocol 118
- Appendix C 121
- Technical Specifications 121
- Keyboard Shortcuts 123
- As-Run Naming Convention 127
- Sample As-Run Log 127
- As-Run Log Page Header 127
- As-Run Log Body 128
- General Requirements 130
- Appendix O 131
- Mechanical Drawing 131
Verwandte Produkte und Handbücher für Video 360-systems Image Server 2000
Video 360-systems MAXX-6T Bedienungsanleitung
(142 Seiten)
(142 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern